FAA-PMA-Approval;
|
U.S. Department |
Transport Airplane Directorate |
|
of Transportation |
Aircraft Certification Service |
|
|
Seattle MIDO |
Federal Aviation |
2500 East Valley Road, Suite C2 |
|
Administration |
Renton, WA 98055-4056 |
Cessna's below:
April 27, 2005 
Mr. Mike Peter
Avtek
25230 45th Ave S
Kent, WA 98032
Dear Mr. Peter:
FEDERAL AVIATION ADMINISTRATION - PARTS MANUFACTURER APPROVAL
In accordance with the provisions of Title 14 of the Code of Federal Regulations (CFRs) part 21,
Subpart K, we have found that the design data, submitted by Avtek based on Test & Computations, and application letter dated April 19, 2005, meet the airworthiness requirements of the regulations applicable to the products on which the parts are to be installed. Additionally, it has been determined that Avtek has established the fabrication inspection system required by part 21 § 21.303(h) at 25230 45th Ave S Kent, WA 98032. Accordingly, Parts Manufacturer Approval (PMA) is hereby granted for production of the replacement parts listed in the enclosed Supplement No. 3. For Cessna Aircraft Models.
You are reminded that the provisions of the Federal Aviation Regulations, noted in our PMA letter of approval dated September 5, 2002, also apply to the enclosed PMA Listing-Supplement No. 3. The enclosed Supplement should be retained with the original PMA Letter as evidence of approval to produce the parts concerned.
Sincerely,
James S. Masciotra, PI
Seattle Manufacturing Inspection District Office
Enclosure:
PMA Supplement No. 3
FEDERAL AVIATION ADMINISTRATION - PARTS MANUFACTURER APPROVAL
Piper's below:
FAA-PMA-Approval Dec 15 2004
u.s. Department of Transportation
Federal Aviation Administration
Transport Airplane Directorate Aircraft Certification Service
1601
Lind Avenue S.w. Renton, Washington 98055-4056DEC I 5 2004
In Reply
Refer To: 150S-04-508
Mr. Michael Peter AvTek Co:25230 45th Ave S. Kent, W A 98032
Dear Mr. Peter:
This is in response to your letter, dated November 25,2004, requesting Parts Manufacturer Approval (PMA) on AvTek door-seal part number Aero-PMA 1001, which is eligible for installation on the Piper Aircraft Models.
We have reviewed the drawings and data submitted and find they meet the requirements of 14 Code of Federal Regulations 21.303(d)(1). The approval of the design via the PMA supplement along with your application has been forwarded to the Seattle Manufacturing Inspection District Office (MIDO). Production approval will be granted after the validation of your fabrication inspection system, and issuance of the FAA-PMA letter and PMA supplement by the MIDO.
Sincerely,
Dor M Anderson
For
Jeffrey E. DuvenManager, Seattle Aircraft Certification Office
December 27, 2004
Mr. Mike Peter
AvTek
25230 45th Ave S
Kent, WA 98032
Dear Mr. Peter:
In accordance with the provisions of Title 14 of the Code of Federal Regulations (CFRs) part 21,
Subpart K, we have found that the design data, submitted by Avtek based on Test & Computations, and application letter dated December 23, 2004, meet the airworthiness requirements of the regulations applicable to the products on which the parts are to be installed. Additionally, it has been determined that Avtek has established the fabrication inspection system required by part 21 § 21.303(h) at 25230 45th Ave S Kent, WA 98032. Accordingly, Parts Manufacturer Approval (PMA) is hereby granted for production of the replacement parts listed in the enclosed Supplement No. 2.
You are reminded that the provisions of the Federal Aviation Regulations, noted in our PMA letter of approval dated September 5, 2002, also apply to the enclosed PMA Listing-Supplement No. 2. The enclosed Supplement should be retained with the original PMA Letter as evidence of approval to produce the parts concerned.
Sincerely,
James S. Masciotra, PI
Seattle Manufacturing
Inspection District Office
Enclosure:
PMA Supplement No. 2
FEDERAL AVIATION ADMINISTRATION - PARTS MANUFACTURER APPROVAL
------------------------------------------END OF LISTING----------------------------------------------
NOTE: Minor design changes (reference 14 CFR part 21 §§ 21.93 and 21.95) must be submitted in a manner as determined by the ACO. Major design changes (reference 14 CFR part 21 §§ 21.93 and 21.97) to drawings and specifications are to be handled in the same manner as that for an original FAA-PMA.
___________________ __ Signature on file ___________
Wolf R. Caliebe, Manager Dorr M. Anderson, Manager
Seattle Manufacturing Seattle Aircraft Certification Office
Inspection District Office
FAA-PMA-Approval Dec 15 2004
u.s. Department of Transportation
Federal Aviation Administration
Transport Airplane Directorate Aircraft Certification Service
1601
Lind Avenue S.w. Renton, Washington 98055-4056DEC I 5 2004
In Reply
Refer To: 150S-04-508
Mr. Michael Peter AvTek Co:25230 45th Ave S. Kent, W A 98032
Dear Mr. Peter:
This is in response to your letter, dated November 25,2004, requesting Parts Manufacturer Approval (PMA) on AvTek door-seal part number Aero-PMA 1001, which is eligible for installation on the Piper Aircraft Models PA-22, PA-23, PA-24, PA-28, PA-30, and PA-32.
We have reviewed the drawings and data submitted and find they meet the requirements of 14 Code of Federal Regulations 21.303(d)(1). The approval of the design via the PMA supplement along with your application has been forwarded to the Seattle Manufacturing Inspection District Office (MIDO). Production approval will be granted after the validation of your fabrication inspection system, and issuance of the FAA-PMA letter and PMA supplement by the MIDO.
Sincerely,
Dor M Anderson
For
Jeffrey E. Duven
Manager, Seattle Aircraft Certification Office
December 27, 2004
Mr. Mike Peter
AvTek
25230 45th Ave S
Kent, WA 98032
Dear Mr. Peter:
In accordance with the provisions of Title 14 of the Code of Federal Regulations (CFRs) part 21,
Subpart K, we have found that the design data, submitted by Avtek based on Test & Computations, and application letter dated December 23, 2004, meet the airworthiness requirements of the regulations applicable to the products on which the parts are to be installed. Additionally, it has been determined that Avtek has established the fabrication inspection system required by part 21 § 21.303(h) at 25230 45th Ave S Kent, WA 98032. Accordingly, Parts Manufacturer Approval (PMA) is hereby granted for production of the replacement parts listed in the enclosed Supplement No. 2.
You are reminded that the provisions of the Federal Aviation Regulations, noted in our PMA letter of approval dated September 5, 2002, also apply to the enclosed PMA Listing-Supplement No. 2. The enclosed Supplement should be retained with the original PMA Letter as evidence of approval to produce the parts concerned.
Sincerely,
James S. Masciotra, PI
Seattle Manufacturing
Inspection District Office
Enclosure:
PMA Supplement No. 2
FEDERAL AVIATION ADMINISTRATION - PARTS MANUFACTURER APPROVAL
------------------------------------------END OF LISTING----------------------------------------------
NOTE: Minor design changes (reference 14 CFR part 21 §§ 21.93 and 21.95) must be submitted in a manner as determined by the ACO. Major design changes (reference 14 CFR part 21 §§ 21.93 and 21.97) to drawings and specifications are to be handled in the same manner as that for an original FAA-PMA.
___________________ __ Signature on file ___________
Wolf R. Caliebe, Manager Dorr M. Anderson, Manager
Seattle Manufacturing Seattle Aircraft Certification Office
Inspection District Office